Featured Member
ID:
CColston
Since: 6/10/2013
From:
Rating: 
(0.0)
Featured Picture
Google Ads
|
 Topic: value of ultrasonic cleaning
|
 
|
| Author |
|
raymondjohnston
Technician
Joined: February.01.05
Location: USA
Online Status: Offline
Posts: 0
|
| Posted: August.24.05 at 9:42pm | IP Logged
|
|
|
I just wanted to throw my two cents in. I have been repairing band
instruments for over 32 years and using "slime away" and "lime and
scale remover" for close to 30 of those years. In May of 2005, the shop
I supervise, purchased a 90 gallon ultrasonic tank. I have been in
complete awe from the first day we used it. Instruments that have been
flushed every summer for many years came out cleaner than ever. We even
had situations where buffing dirt from the factory came out of the
horn. We had to change filters a little more often than suggested, but
the horns are so much cleaner, including the grease and grime between
valves and on sax bodies.
The price tag might slow some down from
obtaining an ultrasonic tank, but I guarantee that the purchase is well
worth it. The tank actually speeds things up a bit.
|
| Back to Top |
|
| |
DamienThomas
Technician
Joined: February.23.05
Location: Australia
Online Status: Offline
Posts: 0
|
| Posted: September.21.05 at 9:45pm | IP Logged
|
|
|
I've also purchased an ultra-sonic unit, however I still get the "pink"
colouring left on the inside of the valve casings. What do other
repairers do to remove this (and from the slide tubing as well)?
Sometimes there is hardly any "pink" at all, but at other times a lot.
If not removed I find the "pink" (ie copper residue) will come off when
the valve oil and the valve rub together and make a gritty black
mixture.
Do other repairers have an issue with this? It also happened when I used slime away.
Overall I do find the ultra-sonic cleaner more effient than previous methods.
thanks Damien
|
| Back to Top |
|
| |
raymondjohnston
Technician
Joined: February.01.05
Location: USA
Online Status: Offline
Posts: 0
|
| Posted: September.21.05 at 10:18pm | IP Logged
|
|
|
While I have had a problem with some of the instruments turning pink,
and its usually the older ones more prone to do this, I have not had a
problem with the pink turning gritty. I have found that some of the
pink disappears when I spray a silver tarnish remover (Badger state
Repair has this) on it, leave it for a minute, then rinse it off. It
gets different degrees of pink off. In addition, we have ran close to a
1000 horns through it, and as long as the filters stay clean, I have
had no problems with grit.
In keeping the filters clean, the one
that is refered to as the pre-pump filter, instead of having to remove
the back to clean that filter, we took a wire mess food strainer and
made a filter in the shape of your finger, and gently pushed about an
inch into the drain hole in the tank. Every now and then, remove that
filter and rinse. Saves pulling the back of to clean it. I still check
the pre-pump filter each time I drain the fluid.
|
| Back to Top |
|
| |
nathanwallace
Technician
Joined: February.06.05
Location: USA
Online Status: Offline
Posts: 0
|
| Posted: September.27.05 at 10:34pm | IP Logged
|
|
|
I'm sold on our
ultra-sonic machine. I have had very little problem with the brass
tarnishing. Especialy when I run saxophones through it. They come out
cleaner, and the brass consistantly retains it's color.
I do
need to be very carefull about what temperature the water is. I have
damaged the lacquer on a couple of older trumpets. I haven't figured
out whether it was the temperature, length of time with the machine
running, or simply the way the lacquer is. I have turned the
temperature down, so I hope that does the job.
|
| Back to Top |
|
| |
SallyGeisert
Technician
Joined: January.17.05
Location: USA
Online Status: Offline
Posts: 2
|
| Posted: September.30.05 at 6:18am | IP Logged
|
|
|
Who did you purchase your ultrasonic cleaner from?
Sally
|
| Back to Top |
|
| |
DaveWeiner
Technician
Joined: January.19.05
Location: USA
Online Status: Offline
Posts: 10
|
| Posted: July.26.07 at 6:11pm | IP Logged
|
|
|
We have a 90 gallon Ultrasonic Power Corp. unit, too. My best employee.
The pink is a reaction from the lead solder with either the brass or the silver plate. Watch where it happens - it's alway at or near a solder joint. The older the horn, the more the pink.
I've use Empires, but it does not remove the pink tarnish.  If it's inside the instrument, the layer of pink tarnish is too thin to impair the operation of the instrument. Outside, you can polish some of it off. Avoid the problem in advance if you can by making sure lacquer is intact.
|
| Back to Top |
|
| |
LarryMueller
Technician & Clinician
Joined: January.20.05
Location: USA
Online Status: Offline
Posts: 24
|
| Posted: July.28.07 at 7:55am | IP Logged
|
|
|
About all I ever have to clean up, are keys on the smaller woodwinds. So, I
bought a cheap ultrasonic ($70, not the cheapest one) from Harbor Freight.
It does a little bit of good, but not enough to bother using it. I'll probably
get around to selling it on eBay some day.
Larry
|
| Back to Top |
|
| |
RobertWhite
Technician
Joined: January.19.05
Location: USA
Online Status: Offline
Posts: 3
|
| Posted: September.22.07 at 9:02pm | IP Logged
|
|
|
Concerning the pink residue left after sonicleaning:
I have been using the larger 90 gallon tank in my shop for awhile and have found that using a battery-powered drill and a soft wire brass brush in combination with Dawn foaming action cleaner works really well.
I discovered the brushes at Kraus Music Products (#547 - 9/16,1/2,5/8,3/4,1 inch), page 32 in the catalogue, if you have it. Contact them at 503-722-7977.
Use the drill at slow speed (less than 1000 rpm) with the cleaner and you will be amazed at the results. You will notice an ochre (yellowish/green) color to the initial foam, but don't worry. Run the brush through a couple of times, rinse and repeat. When the foam is white, rinse with hot water and you're done. I use the various size brushes to clean the inside of all slides, receivers and casings. The outside of the slides get buffed in the normal manner. The valves get brushed with the normal bristle brushes, still using the Dawn foam.
For trombone slides use a strip of 3M green scrubbing pad on a cleaning rod. The fit should be snug, but not too tight. Again, the secret weapon here is the Dawn foam. T-bone slides may take three or four times through to get white foam, but you will be pleased with the results. After the slide has hang dried for awhile, I like to use a strip of double-sided flannel to dry the inside of the outside slide. It leaves everything clean and very smooth.
I hope this helps.
P.S. I set the temperature of my tank at 84 degrees, and have had no laquer problems, with the exception of laquered silver. I have learned not to even try putting laquered silver through the process. Hand clean only.
Edited by RobertWhite on October.18.07 at 12:21pm
|
| Back to Top |
|
| |
|
|
If you wish to post a reply to this topic you must first login
If you are not already registered you must first register
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
|
Powered by Web Wiz Forums version 7.9Copyright ©2001-2004 Web Wiz Guide
This page was generated in 0.0625 seconds.
|
Login
Shout Box
- (10/9 17:13) ChrisHarnett: Doesn't seem very promising
- (10/6 12:46) DriverDrobina: Is this site still active?
- (10/6 12:45) DriverDrobina: I have the same concern
- (6/2 17:51) Wailinfree: is this site still active?
- (6/2 17:51) Wailinfree: is this site still active?
- (4/29 12:46) BENSCHILDGEN: Cleaning snakes nowdays SUCK!
- (12/4 22:44) dparker: Hey Brent!
- (11/26 20:46) crousfrench: I'm back. Did you miss me?
- (10/9 7:18) BENSCHILDGEN: What's going on out there?
- (6/1 18:53) dparker: dparker@ciomit.com www.ciomit.com
- (6/1 18:53) dparker: or we can do an online meeting
- (6/1 18:53) dparker: It can be dangerous. If you could send some pic
- (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
- (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
- (5/25 5:9) BENSCHILDGEN: I had an old tuba that I could not get it apart.
- (5/25 5:8) BENSCHILDGEN: I just do not know much about the whole mechainsm
- (5/24 14:2) dparker: How can I help with the clock springs?
- (5/24 14:2) dparker: How can I help with the clock springs?
- (5/18 5:9) BENSCHILDGEN: MAYBE THIS SITE SHOULD BE LINKED TO FACEBOOK
- (4/26 7:20) BENSCHILDGEN: I need info on tubas with clocksprings for levers
- (4/4 8:34) dparker: Indeed! I will be posting more soon!ore soon!
- (3/30 11:36) BENSCHILDGEN: Let's try to get this site flowing again
- (7/6 19:46) Krch: My favorite is uses for electric soldering guns!
- (6/13 9:0) crousfrench: I still enjoy watching the videos over and over
- (6/13 8:59) crousfrench: I haven't seen anything new in awhile, but
- (5/31 21:36) Krch: articles...articles
|
Active Topics
Memberlist
Search
Help
