Professional Band Instrument Repair Technician Logo

Featured Member

ID: info@colesmusicservice.com
Since: 1/22/2018
From: Sewell United States
Rating: (0.0)

Featured Picture

Google Ads

  Active TopicsActive Topics  Display List of Forum MembersMemberlist  Search The ForumSearch  HelpHelp
Ultrasonics
 PROBIRT Forums » Ultrasonics
Subject Topic: Ultrasonic cleaners Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
Greg
Technician
Technician


Joined: June.27.05
Location: USA
Online Status: Offline
Posts: 6
Posted: May.09.06 at 10:41am | IP Logged Quote Greg

I am interested in investing in an ultrasonic cleaning system. I'm looking for input on the best place to purchase, and what can I expect to pay.

Can this system degrease the instrument prior to lacquering? I don't like the old barrel hot vapor degreasers, a major health hazard.

Any input on who uses these for what applications would be appreciated! Thanks!
Back to Top View Greg's Profile Search for other posts by Greg
 
admin
Admin Group
Admin Group
Avatar

Joined: March.10.05
Location: USA
Online Status: Offline
Posts: 304
Posted: May.09.06 at 9:27pm | IP Logged Quote admin

Hi Greg,

I've been researching them as well.  From the info I've gathered, the ones designed specifically for the type of work we do by Ultrasonic Power Corp are the way to go.  David Arata is the person to talk to there. He'd be a good place to start.

Michelle


Back to Top View admin's Profile Search for other posts by admin Visit admin's Homepage
 
Greg
Technician
Technician


Joined: June.27.05
Location: USA
Online Status: Offline
Posts: 6
Posted: May.10.06 at 12:09pm | IP Logged Quote Greg

Thanks Michelle!!!

Edited by Greg on May.10.06 at 12:09pm
Back to Top View Greg's Profile Search for other posts by Greg
 
trumpet4u
Technician
Technician


Joined: January.19.05
Location: USA
Online Status: Offline
Posts: 1
Posted: June.12.06 at 9:04pm | IP Logged Quote trumpet4u

Hi Greg:
I only do trumpets and found the ones from Ultrasonic Power Corp which are the best but too expensive for me. I purchased a Crest 2800HT Ultrasonic Cleaner. Use a fish filter to filter out the dirt anf use Chem Crest 35 to remove buffing compunds and degrease with a dawn rinse and then a water rinse. It works great for what I'm using it for; and it only cost about $1200. I also use Utra-Power 132-A from Ultasonic Power Corporation to clean the inside of the trumpets. Normally use these chemicals at 110 degrees and they do a great job. It has reduced the amount of time for hand ragging and prelacquer prep.
Back to Top View trumpet4u's Profile Search for other posts by trumpet4u
 
dparker
Newbie
Newbie
Avatar

Joined: March.16.06
Location: United States
Online Status: Offline
Posts: 14
Posted: June.19.07 at 4:51pm | IP Logged Quote dparker

Greg,

Ultrasonic will not work for a pre lacquer routine. Still will not be clean enough. Vapor degreaser still the best. Second best is a wipe down with solvent.

Dan



__________________
Daniel Parker
www.ciomit.com
dparker@ciomit.com
Back to Top View dparker's Profile Search for other posts by dparker Visit dparker's Homepage
 
dflory318
Newbie
Newbie


Joined: June.25.07
Online Status: Offline
Posts: 1
Posted: June.29.07 at 4:36pm | IP Logged Quote dflory318

Greg

I am a student at Western Iowa Tech and we do have an ultrasonic cleaner there. It does work well to clean the instrument, but as Dan said, it does not work well as a de-greaser. Any time we are going to use it on an instrument, Rod will have us test a little piece of the instrument first to see if it will affect the laquer.
Another note, we are having a hard time finding a solution that we like. We started off by using the solution offered for the ultrasonic but found that the filters got clogged very easy and we had to replace them frequently. We have been experimenting with Simple Green and it seems to work a little better.

Hope this helps

Doug
Back to Top View dflory318's Profile Search for other posts by dflory318
 
DaveWeiner
Technician
Technician


Joined: January.19.05
Location: USA
Online Status: Offline
Posts: 10
Posted: July.26.07 at 6:04pm | IP Logged Quote DaveWeiner

Ultrasonics can work as a pre-lacquer, but the methods and solutions that work are pricey and may even compete with your average every day cleaning. If you have a production lacquering shop, talk with UPC about using the right solution and rinsing (you need de-ionized water for a rinse). Anything less than full production lacquering, it's probably not worth it.
Back to Top View DaveWeiner's Profile Search for other posts by DaveWeiner Visit DaveWeiner's Homepage
 
niers1
Newbie
Newbie


Joined: November.19.07
Location: United States
Online Status: Offline
Posts: 2
Posted: January.20.09 at 2:50pm | IP Logged Quote niers1

I was reading one of the "reloader" sites about cleaning cartridges for reloading. The guy who wrote this particular piece tried everything under the sun. Finally,he got his best results with a 50/50 of distilled water and distilled vinegar; adding a few drops of any dishwashing liquid per 8 oz of water.
Have to say, while it doesn't do much for rust or oxidation, it does a pretty decent job on dirt,calcium,oil,rouge etc; and it's inexpensive.
I'd be interested in hearing about any "jungle juice" ideas anyone has used with success.
RS

Edited by niers1 on January.20.09 at 2:51pm
Back to Top View niers1's Profile Search for other posts by niers1
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Powered by Web Wiz Forums version 7.9
Copyright ©2001-2004 Web Wiz Guide

This page was generated in 0.0625 seconds.

Login

Login to view contents and post messages and reviews
Username:
Password:

New Member Registration
Retrieve Lost Password

Shout Box

  • (10/9 17:13) ChrisHarnett: Doesn't seem very promising
  • (10/6 12:46) DriverDrobina: Is this site still active?
  • (10/6 12:45) DriverDrobina: I have the same concern
  • (6/2 17:51) Wailinfree: is this site still active?
  • (6/2 17:51) Wailinfree: is this site still active?
  • (4/29 12:46) BENSCHILDGEN: Cleaning snakes nowdays SUCK!
  • (12/4 22:44) dparker: Hey Brent!
  • (11/26 20:46) crousfrench: I'm back. Did you miss me?
  • (10/9 7:18) BENSCHILDGEN: What's going on out there?
  • (6/1 18:53) dparker: dparker@ciomit.com www.ciomit.com
  • (6/1 18:53) dparker: or we can do an online meeting
  • (6/1 18:53) dparker: It can be dangerous. If you could send some pic
  • (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
  • (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
  • (5/25 5:9) BENSCHILDGEN: I had an old tuba that I could not get it apart.
  • (5/25 5:8) BENSCHILDGEN: I just do not know much about the whole mechainsm
  • (5/24 14:2) dparker: How can I help with the clock springs?
  • (5/24 14:2) dparker: How can I help with the clock springs?
  • (5/18 5:9) BENSCHILDGEN: MAYBE THIS SITE SHOULD BE LINKED TO FACEBOOK
  • (4/26 7:20) BENSCHILDGEN: I need info on tubas with clocksprings for levers
  • (4/4 8:34) dparker: Indeed! I will be posting more soon!ore soon!
  • (3/30 11:36) BENSCHILDGEN: Let's try to get this site flowing again
  • (7/6 19:46) Krch: My favorite is uses for electric soldering guns!
  • (6/13 9:0) crousfrench: I still enjoy watching the videos over and over
  • (6/13 8:59) crousfrench: I haven't seen anything new in awhile, but
  • (5/31 21:36) Krch: articles...articles
SmartFlix.com How-To DVD Rental